|
|
Development of New Approaches in Descaling in the Continuous Production of Steel using High-Pressure Water Jet
Votavová, Helena ; Hloch,, Sergej (referee) ; Čecho, Ladislav (referee) ; Pohanka, Michal (advisor)
The thesis summarizes general and up-to-date knowledge of descaling during the continuous production of the hot-rolled steel and proposes further streamlining of this process in industrial production. The first chapter of the thesis deals with the origin, structure and physical properties of the scales. The second chapter describes the principles of descaling by using a high pressure flat water jet. The third chapter introduces the principles of the experimental methods and describes the used laboratory equipment. The fourth chapter summarizes the description of the particular experiments and their evaluation, and thus represents the focus of the dissertation. It is divided into six sections which independently solve predefined objectives of the dissertation. The first section focuses on the height and structure development of the scales on 54SiCr6 and HDT580X steels. It has been proven that the height of the formed scales increases with the time and temperature of the oxidation. The layered nature of the scales was verified at the same time. The second section examines the effect of the nozzle stabilizer on the focussing and distribution of the impact pressure of the nozzle. Experiments have shown that increase of 11 % of an average maximum nozzle pressure can be achieved, depending on the type of nozzle and the length of the stabilizer. The third section deals with the analysis of shadowgraphy images of water jet structures of the nozzles. A script was developed for analysis of these shadowgraphy photos by an adaptive thresholding. The findings are correlated using a regression analysis with an average heat transfer coefficient. It has been reported that most of the standard nozzle configurations produced disintegrated stream of little droplets at the height of the rolled surface. The fourth section focuses on the area of water jet overlap, especially the area of the so-called washout, where the impact pressure of one nozzle is reduced by the nozzle stream of the other. The influence of the pressure change and the mutual displacement of the nozzles is investigated. The analysis showed that the change of pressure did not have any effect on the percentage of reduction of the impact pressure in the area of the washout. It has been shown that if the area of the washout is wide the descaling efficiency in this area may be reduced. The fifth section builds on the previous section and focuses directly on the areas of waterjet overlaps. The influence of the change of rotation and pitch of the nozzles is studied. Experiments have shown that small changes in nozzle pitch do not have a significant impact on impact pressure and heat transfer coefficient. The effect of nozzle rotation, on the other hand, was a significant factor for the efficiency and homogeneity of the descaling of the surface. The last section deals with the effect of the rolling speed on the heat transfer coefficient in the descaling process. The regression model has shown that with a higher rolling speed there is a reduction in the average heat transfer coefficient. Conclusion summarizes the results of the dissertation and proposes which findings can be used in the industry to make the descaling process more effective.
|
|
|
Development of New Approaches in Descaling in the Continuous Production of Steel using High-Pressure Water Jet
Votavová, Helena ; Hloch,, Sergej (referee) ; Čecho, Ladislav (referee) ; Pohanka, Michal (advisor)
The thesis summarizes general and up-to-date knowledge of descaling during the continuous production of the hot-rolled steel and proposes further streamlining of this process in industrial production. The first chapter of the thesis deals with the origin, structure and physical properties of the scales. The second chapter describes the principles of descaling by using a high pressure flat water jet. The third chapter introduces the principles of the experimental methods and describes the used laboratory equipment. The fourth chapter summarizes the description of the particular experiments and their evaluation, and thus represents the focus of the dissertation. It is divided into six sections which independently solve predefined objectives of the dissertation. The first section focuses on the height and structure development of the scales on 54SiCr6 and HDT580X steels. It has been proven that the height of the formed scales increases with the time and temperature of the oxidation. The layered nature of the scales was verified at the same time. The second section examines the effect of the nozzle stabilizer on the focussing and distribution of the impact pressure of the nozzle. Experiments have shown that increase of 11 % of an average maximum nozzle pressure can be achieved, depending on the type of nozzle and the length of the stabilizer. The third section deals with the analysis of shadowgraphy images of water jet structures of the nozzles. A script was developed for analysis of these shadowgraphy photos by an adaptive thresholding. The findings are correlated using a regression analysis with an average heat transfer coefficient. It has been reported that most of the standard nozzle configurations produced disintegrated stream of little droplets at the height of the rolled surface. The fourth section focuses on the area of water jet overlap, especially the area of the so-called washout, where the impact pressure of one nozzle is reduced by the nozzle stream of the other. The influence of the pressure change and the mutual displacement of the nozzles is investigated. The analysis showed that the change of pressure did not have any effect on the percentage of reduction of the impact pressure in the area of the washout. It has been shown that if the area of the washout is wide the descaling efficiency in this area may be reduced. The fifth section builds on the previous section and focuses directly on the areas of waterjet overlaps. The influence of the change of rotation and pitch of the nozzles is studied. Experiments have shown that small changes in nozzle pitch do not have a significant impact on impact pressure and heat transfer coefficient. The effect of nozzle rotation, on the other hand, was a significant factor for the efficiency and homogeneity of the descaling of the surface. The last section deals with the effect of the rolling speed on the heat transfer coefficient in the descaling process. The regression model has shown that with a higher rolling speed there is a reduction in the average heat transfer coefficient. Conclusion summarizes the results of the dissertation and proposes which findings can be used in the industry to make the descaling process more effective.
|
|
|
The measurement of the velocity of abrasive particles at the suction part of the cutting head
Foldyna, Josef ; Zeleňák, Michal ; Klich, Jiří ; Hlaváček, Petr ; Sitek, Libor
To be able to optimize the design of the abrasive cutting head using numerical simulation, it is necessary to gather as much information about processes occurring in the cutting head as possible. The development of the numerical model of processes occurring in the abrasive water jet cutting head during the process of creation and forming of abrasive water jet is currently in progress at the Institute of Geonics in Ostrava. The verification of the model requires, among others, to determine the behaviour of abrasive particles at the input of the cutting head. Therefore, the visualisation of abrasive particles at the input using various parameters of abrasive jet and its subsequent analysis was performed using shadowgraphy (backlighting) technique and the results are presented in the paper.
Fulltext: content.csg -  DOC
Plný tet: UGN_0398575 - DOC
|
guest ::
